Pool Equipment Installation in
Matthews, NC
Matthews has a deep stock of mature, established pools alongside newer infill builds, and the equipment on those older pads is aging out. We install variable speed pumps, heaters, salt systems, and automation that bring an older pool up to modern efficiency.
Pool Equipment Installation Services in Matthews
From mature pools in Providence Plantation to newer builds in Callonwood and Matthews Plantation, our technicians install every component to manufacturer specifications so you keep full warranty coverage and avoid the noise and inefficiency of aging gear.
Variable Speed Pump Installation
We replace the older single-speed pumps common on established Matthews pads with right-sized variable speed units, plumbing cleanly and programming the speed schedules so your turnover stays efficient and quiet.
Pool Heater Installation
Extend your swim season through the cooler Mecklenburg County evenings. We install gas heaters for fast warm-up and heat pumps for steady maintenance, running the gas line and electrical to code.
Salt Chlorine Generator Installation
Stop hauling chlorine tabs for your Matthews pool. We install the salt cell, wire the control unit, add the initial salt, and set the output so the water stays balanced with far less daily effort.
Automation System Installation
Control pumps, heaters, lighting, and spa features from your phone. We install automation for pools in Sardis Plantation and Shannamara and program the schedules around how your household uses the pool.
Pool Light Installation
Swap a dead incandescent for a long-lasting LED, or add color-changing lights to a Brightmoor pool that never had them. We handle the wet-niche wiring safely and to code.
Equipment Pad Rebuilds
If your pad has decades of layered PVC and mismatched valves, we rebuild it from the ground up with clean plumbing and union valves so future service is simple.
Equipment Brands We Install in Matthews
We install and configure equipment from the major manufacturers Matthews homeowners recognize, including Pentair, Hayward, Jandy, and Raypak. Replacement parts are easy to source locally when the time comes.
Because we install to each manufacturer's specifications, your new pump, heater, or automation system qualifies for its full factory warranty. We register the equipment for you and hand over the documentation on completion.
The Matthews Installation Process, Step by Step
We move through three clear stages so a Matthews upgrade never leaves you guessing about timing or what happens next.
Property Walkthrough
We stop by your Matthews home, assess the pad, verify your plumbing and electrical capacity, and select equipment that fits your pool volume and the way your family uses it.
Equipment Swap
Our team mounts the new components, rebuilds any plumbing that needs attention, and runs all gas and electrical connections to code with labeled, tidy runs.
Fire-Up and Orientation
We start the system, dial in the schedules and water balance, then walk you through the controls so you are comfortable before we leave your Matthews property.
Modernizing Older Pumps in Established Matthews
Pools in Providence Plantation and Matthews Plantation often still run the single-speed pumps installed when the neighborhood was built. Those pumps draw a constant high amp load all day and run louder than a modern variable speed unit, which costs more to operate than necessary.
Our approach is to match the new drive to the actual feet of head your plumbing presents, then set a low-speed primary run that turns the basin over gently across the day. Matthews yards tend to push the pad near a patio or screen porch, so killing the drone of an old motor makes the pool area usable again at the same time it trims the power bill.
Adding Heat to a Matthews Pool
If your pool in Chestnut Place or Weddington Ridge was built without a heater, adding one extends your comfortable swim season well into the fall and warms the water for evening gatherings. We help you choose between a gas heater for fast warm-up and a heat pump for steady, efficient maintenance.
Gas heat comes down to whether your gas line can feed the BTU rating and whether the exhaust has clearance, while a heat pump needs its own breaker and breathing room for the fan. We pull the gas or electrical, hang the unit level, and run it long enough to watch the temperature climb before we pack up.
Automation for Matthews Backyards
An automation system lets you control pumps, heaters, lights, and spa features from your phone or a wall keypad. For busy Matthews households, that means no more walking to the pad at dusk to turn on the lights or start the spa.
We tuck the controller in a weatherproof box, run the low-voltage wire out to each relay, and build your weekly schedule with you standing at the pad. From there you start the spa, dim the lights, or nudge the heat from the app, and we will fine-tune any setting after you have lived with it for a couple of weekends.
Warning Signs a Matthews Pool Needs New Gear
Few pieces of pool equipment fail without first sending signals. If any of these show up at your Matthews pool, it is smart to schedule the replacement before a breakdown leaves you with green water.
- The motor sounds rougher than it used toA pump that grinds or hums more loudly than before is likely running on worn bearings. It may still circulate water, but a shutdown is approaching. Swapping now heads off a mid-season failure.
- Electric bills inch higher each warm seasonA single-speed pump pulls more power as it ages. When your Matthews utility bills rise without any change in pool use, the pump is usually the reason.
- The heater fires then drops outIf the burner lights but the heater cuts off before the water warms, the heat exchanger or control board is typically failing. A new unit is generally more reliable than another repair.
- You are still on a weekly chlorine runIf buying and adding tabs is a weekly chore, a salt chlorine generator ends that errand and leaves the water softer against your skin.
- The pad has calcium crusts or slow valve leaksBuildup on PVC and weeping at the valve handles point to aging plumbing. We can rebuild the pad cleanly while the new equipment goes in.
- Every change is a trip to the padIf you still walk out to flip switches, your pool is a candidate for automation. We can add a control unit without replacing components that still have life in them.
What a Matthews Equipment Install Includes
A Matthews installation covers the equipment, every plumbing and electrical or gas connection, a clean pad finish, the programming, and a full startup with the water balanced. We file the factory warranty registration and hand you the documents.
Before we pack up, we walk you through how to operate and care for the new system, and our team stays reachable for anything that comes up later. The goal is a pool that runs quietly and efficiently and does not demand your daily attention.
Ready for Crystal Clear Water?
Stop stressing over pool maintenance. Let Tarheel Pool Solutions handle it with our crystal clear guarantee.
Neighborhoods We Serve in Matthews
We install pool equipment throughout Matthews, from the established mature pools in Providence Plantation and Sardis Plantation to newer builds in Callonwood, Matthews Plantation, and Brookhaven. Whether your pad is original to the home or brand new, we size the equipment to match.